-
-
-
-
PRODUCTS
-
219 basketball hoop
219 basketball hoop
[Specification]: 2646X1800X3954 (mm)
[Safe Usage Scope] : 14,000 × 15,000 (mm)
[Instructions for Use]: Used in accordance with the rules and methods of basketball.
[Main Features] : Basketball games and training
Category:
Product Description
◆ The main frame is fabricated as a single, integrally bent structure using custom‑made, high‑quality national‑standard steel pipes with a diameter of Φ219×4 mm. The upper and lower tension rods of the basket frame are made from high‑quality national‑standard steel pipes with a diameter of Ф48×2.5 mm.
◆ The verticality of the backboard surface can be adjusted by regulating the upper tension rod; the parallelism between the hoop and the floor can be adjusted by adjusting the lower tension rod; and the verticality and parallelism of the backboard can be finely tuned by adjusting the connection point between the backboard and the support arm. The backboard is supported at five points where it connects to the main frame.
◆ Basketball backboard dimensions: 1800×1050×50 mm; structural dimensions comply with the requirements of GB 19272-2024, section 5.12.1.3. The backboard is made of SMC material, and its strength shall meet the requirements of GB 19272-2024, section 6.12.1.1.3.
◆ The basketball backboard shall have an SMC panel with a thickness of no less than 5 mm, a flange width of no less than 50 mm, and a flange thickness of no less than 7 mm. The rear reinforcing ribs shall adopt a combined V‑shaped and grid‑type structure, with a rib thickness of no less than 6 mm and a rib height of no less than 45 mm.
◆ A reinforcing steel plate is installed on the back side of the rebound shooting area, with dimensions of 722 mm × 150 mm × 5 mm.
◆ The junction between the basketball hoop’s pivot and the backboard is reinforced with high-quality steel plates. The backboard’s embedded nuts and openings shall be waterproofed, and all connections shall use rust‑proof bolts and anti‑theft caps. The backboard surface must remain flat and smooth, with no deformation, delamination, or damage attributable to product quality within eight years.
◆ The basketball hoop is a compression-resistant design, horizontally mounted to the backboard. The steel plate connecting it to the frame is made of high-quality steel, secured with premium, specially designed round-head bolts. The hoop itself is fabricated from solid round steel with a diameter of Φ18 mm, yielding an overall diameter of 468 mm; after being subjected to pressure, it automatically returns to its original position.
◆ The components are cut using a fully automatic CNC sawing machine, ensuring high efficiency and precise positioning. For tube bending, a CNC pipe‑bending machine is employed, delivering accurate angles and an aesthetically pleasing finish. Prior to welding, all parts undergo degreasing to eliminate any residual oil or contaminants from the surface. Welding is performed with a CO₂‑shielded arc welder combined with a mixed‑gas process, producing clean, smooth welds that require no post‑weld grinding. A dust‑collection and treatment system further purifies workshop air, safeguarding worker health. Surface treatment utilizes shot blasting, achieving thorough rust removal while increasing the workpiece’s surface area and enhancing the adhesion of the powder coating. The exterior is finished with a green‑environmental, electrostatically applied powder coating—produced using imported electrostatic spray equipment—ensuring uniform powder distribution, strong adhesion, and superior resistance to acids, alkalis, humidity, heat, aging, and corrosion. This coating is ideal for humid and acid‑rain environments. The product’s paint formulation contains no toxic elements. Powder recovery is handled by a cyclone‑type centrifugal separator, achieving a recovery rate of up to 98.6%, thereby conserving material, reducing dust pollution, and offering convenient operation in an energy‑efficient, environmentally friendly manner.
◆ Adopt a direct‑burial installation method. The burial depth shall be no less than 900 mm, and the buried portion of the column must be integrally connected to the above‑ground portion; welding is prohibited. For the buried section, the main column’s embedded pipe shall be arranged in a cross‑shaped configuration, and the assembly shall be secured by concrete pouring. Soil conditions around the foundation, subgrade treatment, concrete grade, and other related requirements shall comply with national standards.
◆ The equipment nameplate is made of fully stainless steel with a corrosion‑resistant finish, measures 220 × 80 mm, features robust rivets, and has edges that fit tightly against the upright posts to prevent snagging or injury.
◆ The entire machine has no snagging, crushing points, shearing points, or pinching hazards; all apertures and gaps comply with the GB 19272-2024 standard.
◆ The equipment has undergone relevant static load stability tests in accordance with the GB 19272-2024 standard and complies with the standard’s requirements.
◆ The equipment is packaged in a double-layer system: an inner layer of thickened bubble wrap and an outer layer secured with strapping, effectively protecting it from impacts during transit and ensuring it arrives undamaged.
Keywords:
Related products
Online Exhibition Hall
Follow us
Scan to access the WeChat official account.
Contact us
Add：Sanhe Economic and Technological Development Zone, 50 km east of Jianguomen, Beijing
Tel：+86-316-3722333 +86-316-3722971
Fax：+86-316-37233038
E-mail：shguiyuxingty@sina.com
